RPM front and rear Shock Hoops and Body Mounts for the Axial SCX10 incorporate stock shock mount locations along with two upper and two lower shock mounts (for a total of 7 shock mount options) that raise or lower the …
Read More »
Available in black, blue and green, these front suspension arms make the e-Rustler and Stampede 1-1/4” (31.8mm) wider than stock. These Wide Front A-arms extend the front width by exactly the difference in offset between the front and rear wheels. Each RPM A-arm is molded …
Read More »
RPM has updated the Team Associated section of their catalog to include the ProSC 4×4. Since it is the same truck as the Pro-Lite 4×4, all the parts offered for the latter will fit the ProSC, including the front suspension …
Read More »
RPM has released a new gear cover for the 2WD versions of the ECX Torment, Ruckus, Circuit & Boost. This cover has been designed to extend more towards the rear of the vehicle to help eliminate any debris from entering …
Read More »
Just like the front arms from RPM, these rears are molded from a blend of engineering grade nylons for unmatched strength and durability. RPM built oversized bosses around both the inner and outer hinge pins to help prevent hard hits …
Read More »
RPM A-arms for the Helion Dominus SC, SCv2 & TR are molded from a blend of engineering grade nylons for unmatched strength and durability. Crucial design elements include oversized bosses around both the hinge pins and the pivot balls to help …
Read More »
RPM rear A-arms for the Traxxas Nitro Slash are designed with only the necessary mounting holes and nothing more, making this version fit the Nitro Slash exclusively. Eliminating the unneeded holes increases the strength and durability of the A-arms enormously. Additionally, …
Read More »
The RPM Servo-Saver Eliminator Bellcrank for ECX 2wd vehicles eliminates the C-clip design of the stock system in favor of a solid servo-to-tie-rod system. Molded from their trademark blend of engineering grade nylons and backed by a limited lifetime warranty against breakage. …
Read More »
RPM A-arms for the Helion Animus 18SC & 18TR eliminate most of the play at the hinge pins and axle carriers. A tighter suspension system means more precise control of the truck through more accurate camber, caster and toe angle settings. …
Read More »
This Spare Tire Carrier is a simple add-on for the Slash and Slash 4×4 that allows you to bolt on two real spare tires to the back of the truck, perfectly mimicking many popular full-scale off-road desert trucks. The RPM Spare Tire …
Read More »
RPM Oversized Rear Axle Carriers for the ECX Boost, Circuit 2WD, Ruckus 2WD and Torment 2WD utilize 5x11mm bearings compared to the 5x10mm stock units. That little change nearly doubles all load and fatigue ratings over the stock bearing size. Each set of RPM axle carriers …
Read More »
RPM Oversized Front Spindle Blocks for the ECX Boost, Circuit 2WD, Ruckus 2WD & Torment 2WD are designed to solve several issues. The first and most obvious is bearing life. RPM Oversized Front Spindle Blocks bump up the bearing size to …
Read More »
The RPM molded Intake and Blower Set is finely detailed with such finishing touches as blower belt ridges, pulley splines and recessed butterflies in the scoop. It simply to bolts on to almost any hood that is relatively flat by angling the …
Read More »
This new version of the RC10 gear cover has smoother contours than the original, completely seals off the gear case from dirt and debris and has added clearance in several areas. It has a larger, taller area for bigger pinions …
Read More »
The RPM LCG Nerf Bars have added structural support to help strengthen the body and reduce impact forces transferred to the chassis. The additional cross bracing optimizes the rigidity while absorbing additional impact energy. They are available in RPM blue and black. …
Read More »
